The physical adsorption of a polymer, poly(3,3,3-trifluoropropylmethylsiloxane), on aluminized silica particles, without any additional procedure for polymer immobilization, was studied for 180 days to evaluate the new chromatographic support. Morphological, structural, and chromatographic evaluations of the stationary phase were assessed. After the 15th day of adsorption, a sufficient polymer amount adsorbs onto the aluminized silica particles to separate mixtures of compounds in reversed-phase mode. However, after the 60th day, the polymer layer adhesion occurs more strongly, self-coating the aluminized silica particles. The self-coated stationary phases after 60 days showed similar chromatographic profiles with low hydrophobicity and more interactions with polar compounds, characteristics arising from the fluorinated polymer. The aluminized silica support firmly adhered to the polymer layer, resulting in a separation material chemically stable at alkaline conditions, suggesting a surface reactivity like other well-established supports without asymmetrical peaks for polar compounds.

Poly(ethylene oxide-co-dimethylsiloxane) was thermally immobilized on silica particles-Si(PEO)-to separate small polar compounds with water-rich mobile phases. Poly(ethylene oxide-co-dimethylsiloxane) content on Si(PEO) stationary phase was optimized using a central composite design. Infrared spectroscopy, scanning electron microscopy, and thermogravimetric analysis morphologically and structurally characterized the optimized material. Separation of standard test mixtures showed that the Si(PEO) phase had a typical reversed-phase elution order. However, the Si(PEO) phase retained polar compounds better than C18 or aqueous C18 phases under water-rich mobile phases. Under this condition, small changes in the acetonitrile fraction resulted in a marked increase in the retention of some polar drugs on the Si(PEO) phase. A typical condition observed in per aqueous liquid chromatography separations, a more environmentally friendly liquid chromatography approach. On the other hand, hydrophobic compounds showed lower mass transfer rates due to their low solubility in the aqueous mobile phase. Thus, the Si(PEO) phase was more suitable and efficient for separating polar or hydrophilic compounds.

Biodiesel purification by water washing has been proved to be an unattractive process from an economic and environmental point of view. In this work, we propose the use of regenerated cellulose membranes from peanut shell as an alternative in the biodiesel purification. The preparation of the membranes was optimized from a central composite design, resulting in dense and non-porous membranes. However, in contact with biodiesel, the membranes undergo expansion due to the retention of methanol, water, and glycerol molecules, allowing the permeation of fatty acid methyl esters. The filtered biodiesel presents quality parameters, such as total ester content of 98.3 ± 1.4% and free glycerol content < 0.02%, in agreement with the main regulatory agencies. The regenerated cellulose membranes from peanut shell are easily prepared, with high repeatability (relative standard deviation (RSD) < 1.8%) and are presented as an economical and environmental solution for the biodiesel purification.

Buffered solutions, additives, and column temperature are widely used in high-performance liquid chromatography to promote adequate retention of compounds and to improve the chromatographic separation. However, these factors can dramatically reduce the column lifetime. In this work, the effect of column temperature, pH and the salt type and concentration in buffered mobile phases were evaluated on the stability of a typical commercial C18 stationary phase. A method for rapid evaluation of stationary phase degradation caused by these variables was employed to avoid the generation of large volumes of organic waste. By monitoring the performance of stationary phase in the separation of a standard test mixture, it was possible to verify that the pH of the mobile phase is the most drastic condition to reduce the column lifetime. Buffer solutions of inorganic salts as well as the use of temperatures above 40 °C also significantly reduce the column lifetime. However, a column can have its use extended working with low concentrations of organic additives in the mobile phase, under moderated temperature, and adjusting the pH to the safety range of silica-based materials.

This study describes the use of uncured polydimethylsiloxane (PDMS) as a binder agent to prepare carbon paste electrodes (CPEs). A comparative study between the properties of CPEs prepared with PDMS and mineral oil Nujol®, the most common binder agent for CPEs, was carried out. Cyclic voltammetry, electrochemical impedance spectroscopy, and chronoamperometry showed that PDMS-CPEs presented higher electrical conductivity, active electrochemical area, and wider useful potential window compared with Nujol®-CPEs. Moreover, PDMS-CPEs were more stable in aqueous mixtures containing 50% (v/v) of ethanol or methanol than Nujol®-CPEs. PDMS-CPEs have also provided higher sensitivity and lower limit of detection to propranolol than Nujol®-CPE. Therefore, this study demonstrated that PDMS is a promising alternative binder agent able to produce CPEs with superior chemical/electrochemical stability and improved analytical performance.